EMLID REACH RS2

* Gets a fix in seconds
Reach RS2 gets a fixed solution in just seconds and maintains robust performance even in challenging conditions. Centimeter accuracy can be achieved on distances up to 60 km in RTK, and 100 km in PPK mode.
GPS, GLONASS, BeiDou,
Galileo, and QZSS
L1OF, L2OF, L1C/A, L2C,
E1B/C, E5b, B1I B2I
* PPP support
RINEX raw data logs are compatible with PPP services so you can now get centimeter-precise results in any place on Earth. Process RINEX files in an online service and get position with absolute accuracy.
* Built-in 3.5G modem
Reach RS2 features a power-efficient 3.5G HSPA modem with 2G fallback and global coverage. Now corrections can be accessed or broadcasted over NTRIP independently, without relying on an Internet connection on your phone.
* 22 hours on 1 charge
Up to 22 hours of autonomous work when logging data and up to 16 hours as a 3G rover, even in cold weather—no more need to carry spare batteries with you. Reach RS2 can charge from a USB wall charger or a power bank over USB-C.

SIM card slot
Reach RS2 has a built-in 3.5G modem with 2G fallback and global coverage. To get the corrections from NTRIP, you can simply insert the GSM SIM card inside Reach RS2 and set it up by following this guide.

RS-232 port
Reach RS2 can be supplied with constant power over the bottom connector. It's useful when you want to set up RS2 as a permanent base or integrate it with a tractor for precise agriculture. You can also configure the receiver to turn on and off in sync with an external battery. This feature is available in ReachView Settings.
To establish RTK communication with third-party devices, you can connect external radio via RS-232 port.
You can enable the position output to other devices or third-party apps via RS-232 port. You just need to turn on “Position output” in ReachView.

USB-C port
Reach RS2 receiver can be charged via a USB-C cable connected to the power bank or USB adapter.
To establish RTK communication with third-party devices, you can connect external radio via USB-C port.
You can enable the position output to other devices or third-party apps via USB-C port. You just need to turn on “Position output” in ReachView.

LoRa radio port
Reach RS2 has a built-in low-powered LoRa radio for RTK communication between Reach devices. Attach the LoRa antenna and set up the LoRa link in ReachView to work on the baselines up to 8 km in the line of sight.

5/8" thread
Reach RS2 can be placed on the survey pole or tripod using this thread.

Connectivity
LoRa radio
Frequency range868/915 MHz
Power0.1 W
DistanceUp to 8 km
3.5G modem
RegionsGlobal
BandsQuad-band, 850/1900,
900/1800 MHz
SIM cardNano-SIM
Wi-Fi802.11b/g/n
Bluetooth4.0/2.1 EDR
PortsRS-232, USB Type-C

Electrical
Autonomy16 hrs as 3.5G RTK rover,
22 hrs logging
BatteryLiFePO4 6400 mAh, 6.4 V
External power input6–40 V
ChargingUSB Type-C 5 V, 2 A
CertificationFCC, CE

Data
CorrectionsNTRIP, VRS, RTCM3
Position outputNMEA, LLH/XYZ
Data loggingRINEX with events
with update rate up to 10 Hz
Internal storage16 GB
160+ days of logging at 1 Hz

Positioning
StaticH: 4 mm + 0.5 ppm
V: 8 mm + 1 ppm
PPKH: 5 mm + 0.5 ppm
V: 10 mm + 1 ppm
RTKH: 7 mm + 1 ppm
V: 14 mm + 1 ppm
Convergence time~5 s typicall

GNSS
Signal trackedGPS/QZSS L1C/A, L2C
GLONASS L1OF, L2OF
BeiDou B1I, B2I
Galileo E1-B/C, E5b
Number of channels184
Update rates10 Hz GNSS
IMU9DOF